Cooline PT036 Specifikace

INSTALLATION,OPERATION&MAINTENANCEMANUALSINGLE PACKAGED ROOF TOP AIR CONDITIONERS'PT' SERIESMODELS: PT036 - PT360Part Number: 800-213-03

UNIT DIMENSIONSPT180NOTE:1. All dimensions are in mm (dimensions in brackets are in inches).2. Service clearance should be 1200mm (4 feet) on all side

UNIT DIMENSIONSPT215 - PT240NOTE:1. All dimensions are in mm (dimensions in brackets are in inches).2. Service clearance should be 1200mm (4 feet) on

UNIT DIMENSIONSPT300 - PT360NOTE:1. All dimensions are in mm (dimensions in brackets are in inches).2. Service clearance should be 1200mm (4 feet) on

POWERSUPPLY380/415-3-50(4 wire)OPERATION INSTRUCTIONSSTART-UP INSPECTION & CHECK LISTAfter the installation is completed in all respect, the follo

MIN. MAX. FLA RLA LRA HP FLA kW FLA– – 15.2 205/6 7.6/9.1 16.4/18.3 20/20380/415-3-50 342 457 2.3 5.9 42 0.75 5.57.5/10* 11.4/15.2 21.1/25.9 25/3012*

ELECTRICAL DATA342 457 1.9– – 51 607.5/10 11.4/15.2 51/51 60/60 10*/12* 15.2/18.2 51/51 60/6015*/20* 22.8/30.4 51/51 60/6025*/30* 38/45.6

Performex-1TM CONTROLLER : OPERATION & FUNCTIONSThe COOLINE Packaged units are provided with technologically advanced new PerformexTM Controller

7. LEAD/LAG OPERATION: Whenever a compressor needs to be on, the controller will turn on the compressor withthe shorter accumulated run time provided

MAINTENANCE INSTRUCTIONSAIRFLOW ADJUSTMENT (Applicable for PT075 - PT360 only)The airflow could be adjusted by adjusting pulleys of blower motor or be

FORCE SCALESPAN SCALERING"0"LARGE"0"RINGSMALLBELT SPANDEFLECTION =64BELT SPANBG - GROUNDFIELD WIRINGN - NEUTRAL TERMINAL BLOCKL3

Contents PageGeneralModel decoding ...

PREVENTIVE MAINTENANCE SCHEDULE12XXXXXXXXXXXXXFREQUENCY OF MAINTENANCE, MONTHS(FIRST 4 YEARS)I T E MCAUTION: Disconnect power supply and allow all rot

1. Check the power. Switch ON the circuit breaker.Replace fuse if it blown.2. Check wiring against diagram.3. Check and correct it.4. Replace it.1. R

TROUBLE SHOOTING CHART SYMPTOM CAUSES CHECK & CORRECTIVE MEASURE1. Low suction pressure2. High discharge pressure3. Less

JUMPER SETTING ON ECBDIP SWITCH SETTINGSHEATER DATA TABLE(SEE HEATER DATA TABLE)HEATER CONNECTION DETAILSTYPICAL SCHEMATIC WIRING DIAGRAMMODELS : PT03

2. SMOKE DETECTOR OPTIONCRANKCASE HEATER CONNECTION4. HPS CONNECTION OPTIONSTANDARD OPTIONS1. UVM OPTION3. VOLT FREE CONTACT OPTIONSA. UNIT ON & O

TYPICAL SCHEMATIC WIRING DIAGRAMNOTE: 1. Refer to next page for legend, notes & wiring diagram for optional items. 2. Refer to unit con

HPS OPTIONFAN MOTOR CONTROL CONNECTION(APPLICABLE FOR FM WITH T.O.P)NTO NTBL2TO HVTBBM WITH EXTERNAL OLRCONNECTION APPLICABLE FOR 1PH FM ONLYCRANKCASE

HEATER DATA TABLECONNECTION FOR MANUEROP COMP. WITH SSPSCONNECTION FOR COMPRESSORWITH MOTOR OVERLOAD230V(SEE HEATER DATA TABLE)HEATER CONNECTION DETAI

TYPICAL SCHEMATIC WIRING DIAGRAMMODELS : PT180 - PT240 (Dual compressor units)LEGENDAR AUXILIARY RELAYAFS AIRFLOW SWITCHATB AUXILIARY TERMINAL BLOCKBM

TYPICAL SCHEMATIC WIRING DIAGRAMMODELS : PT300 - PT360 (Dual compressor units)NOTE: 1. Refer to next page for legend, notes & wiring diagram for o

C : 1.5 HP ODPD : 2 HP ODPD : 2 HP ODPE : 3 HP ODPF : 3 HP TEFCG : 5 HP ODPH : 5 HP TEFCJ : 7.5 HP ODPK : 7.5 HP TEFCJ : 7.5 HP ODPK : 7.5 HP TEFCL :

TYPICAL SCHEMATIC WIRING DIAGRAMMODELS : PT300 - PT360 (Dual compressor units)LEGENDAR AUXILIARY RELAYAFS AIRFLOW SWITCHATB AUXILIARY TERMINAL BLOCKBM

MODEL NUMBER PT036L PT048L PT060L PT075L PT090 PT100L PT120L PT180L PT215LCOMPRESSOR800-684-08 800-672-52 800-643-01 800-674-78 800-684-09 800-672-52

GENERALGENERAL STATEMENTThis unit is from the PT series that was designed & built for the optimum performance. However, it is required that you be

GENERALThese units are shipped completely assembled, charged, and wired. They do not require any field installation of refrigerant tubing.Units requir

BCAEDBCDAATTENTION TO RIGGERS• Insert 2" nominal pipe through holes in the base rail as shown in the figure below for slings.• Holes in base rail

CONDENSATE DRAIN CONNECTION• Use standard PVC pipe with NPT connection for the condensate drain. Provide a 'P' trap immediately at the conde

UNIT DIMENSIONSPT036 - PT075ABCDEFGHJKLMPT036 - PT060 1460(57.48) 1025(40.35) 1430(56.3) 700(27.56) 163(6.42) 373(14.68) 250(9.84) 500(19.69) 57(2.24)

UNIT DIMENSIONSPT090 - PT120NOTE:1. All dimensions are in mm (dimensions in brackets are in inches).2. Service clearance should be 1200mm (4 feet) on